Smartsign Cloud Service Delivery AU

Thank you for purchasing Smartsign Cloud Service. Please take time to read and follow the instructions.

Please select the type of media player that you have:

PC     Samsung SSSP    LG webOS     Android     SMIL (XMP)

Install Smartsign Player (PC)

Click to download installer.

Click to download documentation

Smartsign Player requires Microsoft .NET 3.5 service pack 1.

1.    Start the installation and follow the on screen instructions.
2.    In the last step of the installation make sure server address is set to au.smartsignmanager.com
Leave username and password to default settings.
3.    Verify connection to the server with the button below server adress.
4.    Save and exit the install.
5.    Start Smartsign Player. Let it run for 30 seconds. A six-digit code will display on the screen.

Continue to section “After installation”

Configure your Samsung Smart Signage Screen (MDC-Series)

1.    Turn the screen off
2.    Using remote: Press MUTE 1 8 2 and then turn the screen on (factory menu)
3.    Select Control – Config Option – LFD Config Option – LFD Launcher
a. Set Launcher Mode to ON
b. Set Server URL Setting to: http://au.smartsignmanager.com/go/reg
(to access special characters: Select the star and flip pages using ”1/2”)
4.    Press Done
5.    Turn off
6.    Turn on
7.    After a short while you should have a registration code on the screen. Write it down.

Continue to section “After installation”

Configure your Samsung Smart Signage Screen (MEC/PEC-Series)

1.    Turn the screen off
2.    Using remote: Press MUTE 1 8 2 and then turn the screen on (factory menu)
3.    Select Control – LFD Option – LFD Launcher
a. Set Launcher Mode to ON
b. Set Server URL Setting to: http://au.smartsignmanager.com/go/reg
(to access special characters: Select the star and flip pages using ”1/2”)
4.    Press Done
5.    Turn off
6.    Turn on
7.    After a short while you should have a registration code on the screen. Write it down.

Continue to section “After installation”

Configure your Samsung Smart Signage Screen (D-Series 2014)

Configure your screen using the setup guide. It will launch the first time you power on your screen or you can launch it manually using the remote. [ Menu -> System -> Setup -> PIN (0000) ]

Complete the setup guide to configure your screen for Smartsign.
Using the remote:
1. Select the language that you wish to use
2. Select Landscape or Portrait mode
3. Set Powersave mode to OFF
4. Configure your network settings
5. Set the Time and Date (not required)
6. Select URL Launcher and enter the appropriate URL from below

  • Landscape: http://au.smartsignmanager.com/go/reg
  • Portrait: http://au.smartsignmanager.com/samsung/register/portrait 

7. Select Done
8. Setup Complete, select OK
9. Select URL Launcher

Continue to section “After installation”

Configure your LG webOS Screen (2014 webOS 1.2)

Using the remote:

1. Power on the screen and wait until it starts up completely
2. Click “SETTINGS”, find the General menu and choose Time & Date. Make sure the date is set correctly. Close the menu when you are done.
3. Press and hold the “SETTINGS” button until a grey square with a chat bubble appears in the top right corner (about 5 seconds)
4. Immediately input “8080” and press OK
5. The “Server Settings” menu should now appear, otherwise repeat from step 2.
6. Set “Application Launch Mode” to “Local”
7. Set “Fully Qualified Domain Name” to “On” and enter:

http://au.smartsignmanager.com/go/reg/lg.zip

8. Select Local Application Upgrade: “Remote” and press OK.
9. “Application Upgrade” will appear, select “Confirm” and press OK.
10. Wait for the upgrade to complete and then press OK.
11. Power Off
12. Power On
13. The panel will now start and load Smartsign. It usually takes 15-25 seconds and it’s normal for the screen to show “No signal” during startup.

Continue to section “After installation”

Download latest version of Smartsign Android Player (Android)

1. Please read this installation guide: Smartsign Android Player Installation

Direct Download: Smartsign Android Player APK
Google Play: https://play.google.com/store/apps/details?id=com.smartsign.android.player

2. Server Adress should be set to: au.smartsignmanager.com
3. After a while you should get a 6 digit code on the screen.

Continue to section “After installation”

Installation Smartsign Hardware Player (IAdea XMP-330 and others)

Click to download documentation

1.    Enter a USB keyboard in the unit
2.    Configure the network (WiFi) or plug in the RJ45
3.    Enter time zone.
4.    Enter content source http://au.smartsignmanager.com/smil/register
5.    Save and exit. Let it run for 60 seconds. A six-digit code is displayed on the screen.

After installation

You should now have a six digit registration code for your screen. Before you can use the screen you need to add it to your account. Follow the instructions below to do so.

If you don’t have your logon details yet, you should receive them shortly after completing the form at the Smartsign Portal page.

Add the screen to your cloud Account:

1. Log on
2. Use the Add Player gadget on the dashboard to add your screen
3. Done

Scroll to Top

Book a personal demo of Smartsign Display Manager

We’ll take you step by step through how you can use our smart solutions for your specific needs. When you book a demo, we’ll contact you, determine your needs and schedule an online demo, often on the very same day.