Smartsign V10 Cloud Service Delivery

Thank you for purchasing Smartsign Cloud Service. Please take time to read and follow the instructions.

Please select the type of media player that you have:

PC     Samsung SSSP    LG webOS     Android     SMIL (XMP)


Install Smartsign Windows Player (PC)

Smartsign WinPlayer 10.7 Installer (64bit only, server 10.6 or higher required)
Smartsign WinPlayer 10.4 Installer (legacy)

Smartsign Player requires Microsoft .NET 4.5 or 4.6-4.8.

1.    Start the installation and follow the on screen instructions.
2.    After installation, launch Smartsign Player
3.    Input the server address: au.smartsigncloud.com
4.    Give the player a name
5.    Save
6.    After a short while you should have a registration code on the screen. Write it down.

Continue to section “After installation”


Configure your Samsung Smart Signage Screen (MDC-Series)

1.    Turn the screen off
2.    Using remote: Press MUTE 1 8 2 and then turn the screen on (factory menu)
3.    Select Control – Config Option – LFD Config Option – LFD Launcher
a. Set Launcher Mode to ON
b. Set Server URL Setting to: http://au.smartsigncloud.com/go/reg
(to access special characters: Select the star and flip pages using ”1/2”)
4.    Press Done
5.    Turn off
6.    Turn on
7.    After a short while you should have a registration code on the screen. Write it down.

Continue to section “After installation”

 

Configure your Samsung Smart Signage Screen (MEC/PEC-Series)

1.    Turn the screen off
2.    Using remote: Press MUTE 1 8 2 and then turn the screen on (factory menu)
3.    Select Control – LFD Option – LFD Launcher
a. Set Launcher Mode to ON
b. Set Server URL Setting to: http://au.smartsigncloud.com/go/reg
(to access special characters: Select the star and flip pages using ”1/2”)
4.    Press Done
5.    Turn off
6.    Turn on
7.    After a short while you should have a registration code on the screen. Write it down.

Continue to section “After installation”



Configure your Samsung Smart Signage Screen (D-Series 2014/E-Series 2015)

Configure your screen using the setup guide. It will launch the first time you power on your screen or you can launch it manually using the remote. [ Menu -> System -> Setup -> PIN (0000) ]

Complete the setup guide to configure your screen for Smartsign.
Using the remote:
1. Select the language that you wish to use
2. Select Landscape or Portrait mode
3. Set Powersave mode to OFF
4. Configure your network settings
5. Set the Time and Date (not required)
6. Select URL Launcher and enter the appropriate URL from below

  • Landscape: http://au.smartsigncloud.com/go/reg
  • Portrait: http://au.smartsigncloud.com/go/reg/portrait 

7. Select Done
8. Setup Complete, select OK
9. Select URL Launcher

Continue to section “After installation”

Configure your Samsung Smart Signage Screen (Tizen/F-Series 2016/H-Series 2017/N-Series 2018)

Start by powering on the screen, then proceed as follows:

1. Select the language that you want to use
2. Display orientation, select the appropriate option, landscape or portrait
3. Auto power off, select “Off (Recommended”
4. Clock Set, Set the date and time
5. Network connection, configure your wired or wireless network connection
6. Play via, select “URL Launcher”
7. Enter the appropriate URL and then select “Done”

  • Landscape: http://au.smartsigncloud.com/go/reg
  • Portrait: http://au.smartsigncloud.com/go/reg/portrait

8. Device Name, leave as is, the setting is not used
9. Complete. select “Done” to continue

Continue to section “After installation”


Configure your LG webOS screen (webOS for signage 1.2 – 4.0)

We strongly recommend that you upgrade the firmware to the latest version prior to installation.

For your convenience, we provide instructions and the most common firmware here: LG – Partner Downloads

Please read and follow the installation guide: Smartsign 10 LG Installation Guide

Use the following URL when asked to input the FQDN setting:
http://au.smartsigncloud.com/go/reg/lg.zip

When you are done you should see a 6 digit code on the screen. Proceed by clicking the link below.

Continue to section “After installation”


Install Smartsign Android Player on an Android device

(QBIC FHD/BXP, Philips D-, P- and Q-line, NEC OPS-DRD, Panasonic OpenPort, Iadea XMP-6xxx and others)

1. Please read the installation guide: Smartsign Android Player Installation Guide

Direct Download: Smartsign Android Player APK

Optional files: Smartsign Android DPI Help APK

2. Server Adress should be set to: au.smartsigncloud.com
3. After a while you should get a 6 digit code on the screen.

Continue to section “After installation”


Installation Smartsign Hardware Player (IAdea XMP-3xx/3xxx)

Only use SMIL for older linux based XMP devices. Use Android instructions for newer.

1.    Enter a USB keyboard in the unit
2.    Configure the network (WiFi) or plug in the RJ45
3.    Enter time zone.
4.    Enter content source http://au.smartsigncloud.com/smil/register
5.    Save and exit. Let it run for 60 seconds. A six-digit code is displayed on the screen.


After installation

You should now have a six digit registration code for your screen. Before you can use the screen you need to add it to your account. Follow the instructions below to do so.

If you don’t have your logon details yet, you should receive them shortly after completing the form at the Smartsign License Portal.

Add the screen to your cloud Account:

1. Log on to https://au.smartsigncloud.com
2. Go to My Devices
3. Click Register screen and follow the instructions (bottom right corner)

Scroll to Top

Book a personal demo of Smartsign Display Manager

We’ll take you step by step through how you can use our smart solutions for your specific needs. When you book a demo, we’ll contact you, determine your needs and schedule an online demo, often on the very same day.